Also, so far this only seems to happen when the stove hasn't been lit for very long and I have to leave the house, so I close the dampers in case the fire gets out of control and theres nobody there to close the dampers down.
Mutz wrote: » Hi Stovefan, We want to replace our gas fire in the sitting room with a non boiler stove. The sitting room is 18' x 13'. The house has Gas central heating however we would like to install the stove for the evening in winter. The house is timber frame but there are blocks behind the fireplace and the chimney is flued with pots. We are choosing between two Stoves, namely the San Remo Insert Stove and the Firefox NON-Insert Stove. They are around the same price. I have attached three pics below of our fireplace and of the two stoves we are choosing from. Our questions to you is, which in your opinion would be our best option given our fireplace set up? Which one would give out the best heat How could we set up the Firefox stove if we were to choose it? (Would we have to close up the fireplace and have the stove sitting on the hearth?) We got quotes from Clane Fireplaces of: 1. 680euro for the San Remo + installation (no mention of flue lining) 2. 750euro for the Firefox + installation (no mention of flue lining) Has anyone had any dealings with Clane Fireplaces that they would like to share? All comments welcome
Theimprover wrote: » My gas fire stove cuts out after about an hr from been turned on and about 10-20 mins everytime after that. Anyone know what the problem is?
Theimprover wrote: » bump
Stove Fan wrote: » Hi:) I would definately install an inset stove as if you install a freestanding stove it would have to sit on the hearth. The hearth would need to be extended forward to give 300mm in front of the stove. The other issue that will be a problem is the wooden surround being too near the freestanding stove. The inset stove would be much simpler to install and need the least alterations If your clay lined flue passes the smoke pellet test then the chimney won't need to be lined. Most inserts don't require a flue liner and just slot into the fireplace and backfilled with a vermiculite/sand/cement mix. Have a look at this inserthttp://www.stovesareus.co.uk/catalog/aarrow-ecoburn-5-inset-multifuel-woodburning-stove-p-6423.html Or my favourite if you can go the extra. Around £900 in the Uk or the enigma 3.5 £750. 3.9kwhttp://www.woodwarmstoves.co.uk/products/fireview-range/4kwinsetfireview.ashxhttp://www.youtube.com/results?search_query=woodwarm+stoves&oq=woodwarm+stoves&aq=f&aqi=&aql=&gs_sm=s&gs_upl=31015l37073l0l39104l15l15l0l5l5l0l486l2220l3.2.3.0.2l10l0 I calculated your room needs 4kw to heat it or less depending on the level of insulation. Stove Fan:)
Reyman wrote: » Hi Stovefan, Any idea where it might be possible to see those Fireview inset stoves around Dublin? They seem to be pretty unknown in most of the fireplace shops! Thanks
Glorneys 42 Sundrive Road, Kimmage, Dublin 12 Ireland Tel: 00353 1492 1355 Fax :- 00353 1492 1732
stephendevlin wrote: » I would like to install a stove on the rear of the open fire in the kitchen Are there any issues with that type of instillation? We have Oil at the moment on both floors the cylinder tank is 750mm x 450mm I presume its a vented system can provide pics necessary. The hotpress is right above where I would like to install the stove. I know the pipework is the major issue is it only a matter of a hot and cold feed from the hotpress (directions wise)
troutfeet wrote: » hi I'm getting a freestanding multiburner installed and i was talking to the guy who is installing it earlier. I asked him about the single wall flue and how to stop the smoke escaping into the room. he says that you just stack the flues on top of each other. I find that hard to believe would there not be some sort of sealent required @ the joints? I don't really trust this guy but if what he says is true grand i just want to make sure. thanks in advance
irishproduce wrote: » Here is a question. Stove Fan, do you install Stoves outside of work or is it just advice you give? I searched and don't think anyone has asked you. I ask because you seem like you know your stuff and seem very competent. I am a newb to stoves and have been reading some of your contributions and I am impressed. If you install them off the job, let me know. I have been quoted €750 to buy and have installed a Dimplex WST5. I hadn't expected it to be that much but that may very well be normal.
irishproduce wrote: » Here is a question. Stove Fan, do you install Stoves outside of work or is it just advice you give? I searched and don't think anyone has asked you. I ask because you seem like you know your stuff and seem very competent. I am a newb to stoves and have been reading some of your contributions and I am impressed. If you install them off the job, let me know.
irishproduce wrote: » Pity!! That stove is €379 in the Co-Ops at the moment and €399 on thegascompany.ie meaning installation is around €400 - €450. is that really right? More than the cost to the unit itself!! On a side note, after reading your posts, I don't know why you don't do tommers or nixers or whatever you want to call it in your free time. Obviously if you don't need the cash, grand but you seem to love it! Thanks for your advice by the way!
Countryboymike wrote: » I have sourced a 22kw Multifuel stove called the Fireglow. Have any of you guys got one or heard of them .Bit nervous about closing the deal as I have never heard of the make.It says she will power 12 rads. Thanks Guys.
seosamh wrote: » Hi Stovefan, I recently got an extension built to my house of about 25 square metres so there is about 4m*4m living area and a 4m*2.5m galley kitchen, all open plan. I am wondering if it is possible to put in a suitable stove in the corner of the living area and how it could be done. I would need to bore a hole in the end wall to accommodate a flue and am wondering if there are any regulations for this. This is a single storey structure so would the flue pipe need to extend a certain height above the roof (apex)? Do I need to be mindful of neighbours- not just for fire but would there be a lot of smoke considering it would be exiting at a lower height. Do some fuels burn cleaner than others? Also can you recommend a suitable stove. I was looking at some by the Swedish manufacturer Contura but althought they are sleek, they are probably very expensive. But I think they are wood only and I am leaning towards a multi. Also this would be a stand alone as I don't need to to heat rads. Thanks.
Stove Fan wrote: » Hi:) I have calculated that you need a 5kw stove or up to 6kw output if the rooms have poor insulation. The best way to install the stove would be to use a twin wall insulated stainless steel chimney either out through the wall and up or vertical straight through the roof. The flue pipe manufacturers and stoves installation instructions must be followed. There are regulations regarding clearance above roofs but I can't really comment further as some pictures would help enormously. Budget around 500-1500 for the flue depending on how high it needs to be. It may have to go the full height of the house. If the flue is too low you could get complaints from neighbours with the smoke blowing into their home. It would be best to burn a smokeless fuel like ecobrite to minimise the smoke from the flue. What look are you wanting? These below are traditional looking. Good stoves are the morso squirrel. Charnwood. woodwarm fireview Dunsley highlander Others worth considering. Stovax stockton 5 Villager solo/duo/ Chelsea. Hunter herald 5. There are many others:) If you want further stove info just ask:) Stove Fan:)
ccmp wrote: » From experience, I would recommend using single wall up to ceiling and twin wall at transit through roof and on to finished height. The amount of heat transfer from single wall flue to the room makes this the best option.
seosamh wrote: » Thanks Stovefan, What you wrote about the flue possibly needing to reach above the second storey height has put me thinking. In my case, the single storey extension is L-shaped wrapping around the two storey back of the house. So I could perhaps go through the roof in order to tie the flue externally to the old structure to reach the required height. I will try to get some photos to make this clearer. So costing this what would you estimate? Stove = 400 Flue 2metres internally and 4 metres externally and ties = ? Cost of installation ( installer needs to make changes to the slate roof, install flashing etc ) =? Thanks.
Mutz wrote: » Hi Stovefan again! I've done a hell of a lot of research now at this stage about getting an insert Stove - probably a Boru An Chroi Beag (€550). I'm still confused on a number of things as we are getting very conflicting instructions on the installation. One stove supplier is saying flue lining is not needed and the other is saying it is required. We are going to get the gas fire taken out. Now behind this unit is just a void. There is no fireback behind the gas fire meaning just blocks leading up into a Flue Gather and pots above. Am I correct in saying that I need to get a fireback installed first and would you agree in the way in which this fireback is installed? The fireplace has never been used for solid fuel and I assume the chimney pots in this new build are in good condition. Would you recommend I get the chimney lined (given its good condition) and connect to the inset stove or would I get away with just inserting the stove into the fireback and let the chimney look after the fumes? I have been quoted €1000 for installation, excluding the stove unit. The chimney is a standard two storey height (9 metre approx). What's your opinion on this price? The hearth and the fireplace surround are all one piece of marble. Would we get away with keeping these or will they crack when using an inset stove? Thanks again for the valuable opinions you have given everyone here.
Stove Fan wrote: » Mutz wrote: » Hi Stovefan again! I've done a hell of a lot of research now at this stage about getting an insert Stove - probably a Boru An Chroi Beag (€550). I'm still confused on a number of things as we are getting very conflicting instructions on the installation. One stove supplier is saying flue lining is not needed and the other is saying it is required. We are going to get the gas fire taken out. Now behind this unit is just a void. There is no fireback behind the gas fire meaning just blocks leading up into a Flue Gather and pots above. Am I correct in saying that I need to get a fireback installed first and would you agree in the way in which this fireback is installed? The fireplace has never been used for solid fuel and I assume the chimney pots in this new build are in good condition. Would you recommend I get the chimney lined (given its good condition) and connect to the inset stove or would I get away with just inserting the stove into the fireback and let the chimney look after the fumes? I have been quoted €1000 for installation, excluding the stove unit. The chimney is a standard two storey height (9 metre approx). What's your opinion on this price? The hearth and the fireplace surround are all one piece of marble. Would we get away with keeping these or will they crack when using an inset stove? Thanks again for the valuable opinions you have given everyone here. Hi:) I wouldn't think a fireback will be necessary unless they state it must be fitted. On some inserts you have to remove the fireback anyway in order to create the right depth. After the insert is fitted in place the space behind and to the side and above the fire will be filled up with a vermiculite/sand and cement mix, like shown in the video clip. This is important as it prevents heat loss and directs it more into the room. It would be better to line the flue if you can afford the extra expense. It will draw better and make cleaning the flue easier. With regard the price you would be looking at between 450-600 for the liner depending whether its 316 grade or 904, the 904 grade is better. Plus any other consumables ie chimney cowel, vermiculite mix etc. The only possible problem is the marble surround but being an insert it should be ok the main worry for me is the marble above the fire, exposed to the most heat. What does your installer think? Stove Fan:)
